Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
See the difference
Before
After
Before
After
Before
AfterHow Much Does Chimney Liner & Rebuild Cost in Clarksville?
In Clarksville, a stainless steel flexible liner runs roughly $1,900 to $4,200 installed, and a chimney rebuild costs about $3,800 to $12,000 depending on how many flues and how much masonry is involved. HeatShield ceramic resurfacing, a middle option that screens deteriorating clay tiles instead of pulling them out, typically lands between $1,100 and $2,400. The written estimate always sets the final price, since every flue is different.
Chimney Liner & Rebuild Cost Breakdown (2026)
Here’s how the numbers shake out for a typical wood-burning flue in a Clarksville home. Prices are estimated ranges for the local market, not quotes. A real visit to the house, a camera look inside the flue, and a look at the crown and flashing set the actual figure.
| Work | Typical Estimated Range | What It Covers |
|---|---|---|
| Flexible stainless liner, one flue | $1,900 – $4,200 | Top plate, cap, insulation wrap, and DuraFlex flexible liner for a wood flue or gas insert vent |
| HeatShield ceramic flue resurfacing | $1,100 – $2,400 | Screening cracked or spalling clay tiles back to a smooth, sealed surface |
| Liner with new top plate and crown repair | $2,400 – $5,000 | Liner install plus fixing the crown, which is where most water damage starts |
| Partial rebuild (crown down to the roofline) | $3,800 – $7,500 | Tearing out failed masonry above the roof, relaying brick, new crown and flashing |
| Full rebuild (ground to top) | $7,500 – $12,000 | Stripping a failing stack or a chimney on a leaning foundation, then rebuilding the whole structure |
| Rebuild plus new liner | $6,000 – $14,500 | The full job: sound masonry and a code-compliant flue done together |
| Gas insert liner, straight run | $1,400 – $2,900 | Smaller-diameter liner sized to the appliance, with the vent cap |
The gap between the low and high end of each line comes down to liner length and diameter, how many offsets the flue has, and whether the chimney is easy to reach. A straight, single-story run is on the low side. A tall two-story stack with a dogleg and a roofline that needs ladder access pushes it up. Adding a rebuild to a liner job stacks the work because the masonry has to be sound before the liner goes in, and the old flue brush and prep work runs in the same visit.
What’s driving the totals here is the housing stock. A lot of Clarksville homes were built in the middle of the last century with clay tile flues that have now seen decades of heating cycles. Tile cracks. Hot flue gases get behind a crack and reach the framing. A liner corrects that. A rebuild is for when the masonry itself is too far gone to hold a liner. We carry the parts to solve either one, so you don’t need a second contractor after the inspection.
What Affects Chimney Liner & Rebuild Pricing in Clarksville
- How tall and how crooked the flue is. Liner is priced by the foot, and every offset or jog in the flue adds prep work before the liner will pass cleanly. A straight run on a single-story house is the cheapest version of this job.
- What the inside of the flue looks like. If the clay tiles are intact but rough, HeatShield resurfacing handles it for less than a full liner. If they’ve collapsed or never existed, you’re looking at a liner or a rebuild. The camera inspection decides which, and it happens before any money changes hands.
- Whether the crown and flashing are holding. Clarksville’s hot, humid summers and the freeze cycles in a Middle Tennessee winter both work on masonry. Water gets into a cracked crown, freezes, and pushes brick apart. Fixing the crown during liner work costs far less than a rebuild a few years later.
- Masonry condition and the amount of teardown. Rebuild pricing tracks the square footage of brick coming off and going back on. Spalling faces, crumbling mortar joints, and cracks that run through the stack all mean more demolition before anything new goes up.
- Appliance type. A wood-burning fireplace, a gas insert, and a wood stove each need a different liner diameter and venting setup. A gas insert liner is smaller and cheaper than a full wood-flue liner, but it still has to be sized to the appliance, not picked off a shelf.
- Access and roof pitch. A steep roof or a chimney tucked behind a dormer slows the work and means more setup. It’s a real line in the estimate, not padding.
Liner Repair, Resurfacing, or Full Rebuild: Which Do You Need?
The honest answer is that most Clarksville chimneys that pass a camera inspection need a liner, not a rebuild. A rebuild is the right call when the brick and mortar can no longer support a liner or when the chimney is structurally unsafe. Everything in between has options.
- HeatShield resurfacing is the repair-tier middle path. It works when the clay tiles are cracked but still in place, and it costs less than pulling them and running a new liner. It’s a method sweep-only operations don’t carry, which is why a lot of homeowners hear “you need a full rebuild” when resurfacing would have done the job.
- A DuraFlex flexible liner is the standard fix for a compromised or unlined flue. It’s the professional-grade system we install for wood and gas appliances.
- A partial or full rebuild is for failed masonry. If the crown is gone, the flashing is shot, and the brick faces are flaking, a liner alone just puts a new pipe inside a crumbling shell.
We work with six professional chimney trade brands – DuraFlex, HeatShield, Gelco, Olympia Chimney, Famco, and Copperfield – which means the right component is on hand rather than special-ordered around your schedule. If the inspection turns up a problem, the fix happens in the same relationship instead of sending you back out to find someone who can do the repair.
The safe call here matters. Cracked tiles, a missing liner, or a failing stack are fire-safety problems, not cosmetic ones. A chimney that vents into framing or lets creosote collect against wood is a fire waiting on a cold night. We don’t hand out do-it-yourself instructions for liner or masonry work because the failure mode is a house fire, and a trained professional should make that call in person.
How to Save on Chimney Liner & Rebuild in Clarksville
There’s no coupon that beats catching a problem early. A liner installed before the masonry fails costs a fraction of a rebuild, and a crown repair done during routine service costs less than the water damage it prevents. If you’re still in the “should I even look” stage, our chimney sweep Clarksville service includes the inspection that tells you which category you’re in.
- Get the camera inspection first. A photo of the flue tells you whether you need resurfacing, a liner, or a rebuild. Guessing at it is how people overpay for work they didn’t need.
- Ask about HeatShield before agreeing to a full liner. If your tiles are cracked but intact, resurfacing is the lower-cost repair. Ask for it by name.
- Bundle the crown and flashing with liner work. One visit, one set of setup costs, and water stays out of the new system from day one.
- Fix the crown while it’s small. A crown repair is a modest line item. A crown ignored for years becomes a rebuild.
- Have the dryer vent cleaned at the same time. It’s a separate fire hazard in the same house, and handling both in one appointment saves the second trip.
- Start with a free estimate. We price per job from a written estimate and there’s no charge to get one. Call (866) 942-9931.
What Happens When You Call
We ask what you’re seeing – smoke backing up, a smell, water staining on the ceiling near the chimney, or just a home you bought that’s never had a chimney check. Then we schedule a visit, run a camera down the flue, and show you what it found. You get a written estimate that separates the liner, the masonry, and anything else, so you can decide what to do now and what can wait. Call (866) 942-9931. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
If you’re in the middle of a home purchase or move, we can assess a chimney before you light the first fire. Read more about the neighborhoods we cover on our Clarksville page.
FAQs – Chimney Liner & Rebuild Cost
How much does a chimney liner cost in Clarksville?
A flexible stainless liner in Clarksville typically costs $1,900 to $4,200 installed for a single flue, with gas insert liners at the lower end around $1,400 to $2,900. The written estimate sets the final price. Call (866) 942-9931 for an exact quote – estimates are free.
Is it cheaper to reline a chimney or rebuild it?
Relining is almost always cheaper – roughly $1,900 to $4,200 versus $3,800 to $12,000 for a rebuild. A rebuild is only necessary when the masonry itself has failed and can’t hold a liner. The camera inspection answers that. Call (866) 942-9931 and we’ll tell you which one you actually need.
How much does HeatShield resurfacing cost in Clarksville?
HeatShield ceramic resurfacing runs about $1,100 to $2,400 and is the middle option between doing nothing and a full liner. It’s for cracked or spalling clay tiles that are still structurally sound. Call (866) 942-9931 for a free estimate on your flue.
Can you repair a chimney liner the same day?
Liner installs and resurfacing can often be done in a single visit if the materials are on hand, which is why we stock the professional trade brands rather than special-ordering. Rebuilds span multiple visits. Call (866) 942-9931 and we’ll book you into the next opening, Sunday through Friday, 7am to 7pm.
What does a chimney rebuild cost in Clarksville, and why so much?
A partial rebuild runs about $3,800 to $7,500 and a full rebuild $7,500 to $12,000. The price tracks teardown and brick square footage, and a rebuild plus a new liner together lands around $6,000 to $14,500. It’s real masonry work, not a patch. Call (866) 942-9931 for a free written estimate.
Pricing reflects the Clarksville market as of 2026. Chimney Sweep Clarksville offers free estimates – call (866) 942-9931.
Written by the team at Chimney Sweep Clarksville.
What Our Customers Say
"Level two inspection before we bought the house. The report was detailed enough to use as a negotiating point and he explained every photo in it."
- Jeff Reed"Creosote buildup was worse than I realized. He measured it, showed me the glazing on the flue with the camera, and was honest that we were closer to a chimney fire than I wanted to hear."
- Eric Novak"Fixed the problem and it hasn't come back. Took two visits though, because the right part had to be ordered. They didn't charge me for the second trip, so I can't complain too much."
- Shanice Jackson